China China PCB 6Layer Gold Finger Blue Soldermask Board| YMS PCB factory and manufacturers | Yongmingsheng
សូមស្វាគមន៍មកកាន់គេហទំព័ររបស់យើង។

China PCB 6Layer Gold Finger Blue Soldermask Board| YMS PCB

សង្ខេបខ្លី:

Gold finger is the connector at the edge of boards. It is similar to fingers, so we called gold finger, please see the following pictures. It is used to protect the ក្រុមប្រឹក្សាភិបាលសៀគ្វីដែលបានបោះពុម្ព prototypes from wear and tear.

ប៉ារ៉ាម៉ែត្រ

Layers: 6L High Tg FR4 Material

ការគិតរបស់ក្រុមប្រឹក្សាភិបាល: 2.0 ម

សម្ភារៈមូលដ្ឋាន: S1000-2 ខ្ពស់ tg

ប្រហោងអប្បបរមា៖ ០,២ ម។ ម

ទទឹងបន្ទាត់អប្បបរមា / ការបោសសំអាត: 0.075 មម / 0.075 មម

ការបោសសំអាតអប្បបរមារវាងស្រទាប់ខាងក្នុង PTH ដល់បន្ទាត់: 0.2 ម

ទំហំ: 214mm × 98mm

សមាមាត្រសមាមាត្រ: ១០: ១

Surface treatment:ENIG+ Gold Finger

Differential impedance 90+8/-8Ω

ចរិតលក្ខណៈនៃដំណើរការ :  gold finger

Applications: Consumer electronics


ផលិតផលលំអិត

ផលិតផលស្លាក

What is the Gold Finger?

Gold finger is the connector at the edge of boards. It is similar to fingers, so we called gold finger, please see the following pictures. It is used to protect the printed circuit board prototypes from wear and tear.

The surface treatment of the gold finger PCB

Electroplated nickel gold: Thickness up to 3-50u", due to its superior conductivity, oxidation resistance and wear resistance, it is widely used in gold finger PCB that require frequent plugging or PCB ក្រុមប្រឹក្សាភិបាល that require frequent mechanical friction. While the cost of gold plating is extremely high, it is only applied to local gold plating such as gold fingers.

Immersion Gold: The thickness of conventional is 1u", up to 3u". It is widely used in high-precision PCB board with button position, bonded IC, BGA, etc. due to its superior conductivity, flatness and solderability. The gold finger PCB with low wear resistance requirements can also choose the entire board immersion gold process. The cost of the immersion gold process is much lower than that of the electric gold process. The color of the immersion gold process is golden yellow.

Goldfinger design in PCB

Goldfinger is an electrical interface. The common packaging form and appearance of PCB are as follows. When the appearance and packaging similar to the figure below are seen in the PCB design, the first reaction is to see them on the boardGold finger.

The easier way for goldfinger to judge is to have both the TOP and BOTTOM of the device

PIN device;It will look like the u-slot in the picture below.

When there is a goldfinger on the board, you need to work on the details of the goldfinger.

https://www.ymspcb.com/12layer-hard-gold-hdi-yms-pcb.html

https://www.ymspcb.com/12layer-hard-gold-hdi-yms-pcb.html

Details of goldfinger in PCB:

1) in order to increase the wear resistance of goldfinger, goldfinger usually needs to be plated with hard gold.

2) goldfinger needs chamfering, usually 45°, other angles such as 20°, 30°, etc.

If there is no chamfer in the design, there is a problem.In the figure below, the arrow is 45 degrees

chamfering

https://www.ymspcb.com/12layer-hard-gold-hdi-yms-pcb.html

The 45° chamfering Angle in PCB is shown in the following figure:

hard gold pcb3

3) goldfinger needs to do the whole block of anti-welding window opening treatment, and the PIN does not need to open the steel net;

4) a minimum distance of 14mil from the tip of finger is required for the sink tin and silver welding pads;Recommended design

When the pad is more than 1mm away from the finger position, including the through hole pad;

5) do not coat goldfinger with copper;

Below is a goldfinger design for reference

hard gold pcb4

6) all layers of the inner layer of goldfinger need to be copper whittled, usually with a width of 3mm;

It can be done with half finger and whole finger.In pci-e design, there are also fingers

Remove all copper from the mingoldfinger area;

Goldfinger's resistance will be low, and cupping (hollowing out under the finger) will reduce it

The impedance difference between the impedance line and the impedance line is also beneficial to ESD.

Suggestion: cut all the copper under the goldfinger welding pad

https://www.ymspcb.com/12layer-hard-gold-hdi-yms-pcb.html

 

អាន​ព័ត៌មាន​បន្ថែម


https://www.ymspcb.com/6layer-gold-finger-board-yms-pcb.html



  • មុន:
  • បន្ទាប់:

  • សរសេរសាររបស់អ្នកនៅទីនេះហើយផ្ញើវាទៅឱ្យពួកយើង
    កម្មវិធី WhatsApp លើបណ្តាញជជែកកំសាន្ត!