Double sided pcb Normal pcb Lead free HASL Counterbore Manufacturer | YMS PCB
HAL(Lead Free), the full name is Hot Air leveling with Lead Free. Compared with HASL, the main difference for HAL(Lead Free) is the element of material which do not contain Lead(Pb), so it’s RoHS Compliant and it’s much more popular and widely used in výroby .
HAL(Lead Free) requires higher run temperatures for lead free solder and longer contact time, the production cost for HAL(Lead Free) is slightly higher than HASL(Tin/Lead).
The manufacturing process of HAL(Lead Free) is similar to HASL(Tin/Lead), the circuit boards will be submersed in molten solder(Lead Free). This solder will cover all the exposed copper surfaces. Upon retraction from the solder, high pressure hot air is blown over the surface through air knives, this levels the solder deposit and removes the excess solder from the surface of printed circuit boards.
Úvod k doske s plošnými spojmi
Normálna doska plošných spojov: Most PCBs for simple electronics are simple and composed of only a single layer. More sophisticated hardware such as computer graphics cards or motherboards can have 2 or multiple layers, sometimes up to twelve.
A printed circuit board (PCB) mechanically supports and electrically connects electrical or electronic components using conductive tracks, pads and other features etched from one or more sheet layers of copper laminated onto and/or between sheet layers of a non-conductive substrate. Components are generally soldered onto the PCB to both electrically connect and mechanically fasten them to it.PCBs can be single-sided (one copper layer), double-sided (two copper layers on both sides of one substrate layer), or multi-layer (outer and inner layers of copper, alternating with layers of substrate). Multi-layer PCBs allow for much higher component density, because circuit traces on the inner layers would otherwise take up surface space between components. The rise in popularity of multilayer PCBs with more than two, and especially with more than four, copper planes was concurrent with the adoption of surface mount technology.
What is the difference between a Countersink and a Counterbore?
Normálne možnosti výroby DPS YMS:
| Prehľad výrobných kapacít YB Normal PCB | ||
| Funkcia | schopnosti | |
| Počet vrstiev | 1-60L | |
| K dispozícii je normálna technológia PCB | Priechodný otvor s pomerom strán 16: 1 | |
| pochovaný a slepý cez | ||
| Hybrid | Vysokofrekvenčný materiál ako RO4350B a FR4 Mix atď. | |
| Vysokorýchlostný materiál ako M7NE a FR4 Mix atď. | ||
| Materiál | CEM- | CEM-1; CEM-2 ； CEM-4 ； CEM-5 atď |
| FR4 | EM827, 370HR, S1000-2, IT180A, IT158, S1000 / S1155, R1566W, EM285, TU862HF, NP170G atď. | |
| Vysoká rýchlosť | Megtron6, Megtron4, Megtron7, TU872SLK, FR408HR, série N4000-13, MW4000, MW2000, TU933 atď. | |
| Vysoká frekvencia | Ro3003, Ro3006, Ro4350B, Ro4360G2, Ro4835, CLTE, Genclad, RF35, FastRise27 atď. | |
| Ostatné | Polyimid, Tk, LCP, BT, C-ply, Fradflex, Omega, ZBC2000, PEEK, PTFE, na keramickej báze atď. | |
| Hrúbka | 0,3 mm - 8 mm | |
| Max. Hrúbka medi | 10OZ | |
| Minimálna šírka a medzera | 0,05 mm / 0,05 mm (2 míle / 2 míle) | |
| BGA PITCH | 0,35 mm | |
| Minimálna mechanická vŕtaná veľkosť | 0,15 mm (6 mil) | |
| Pomer strán pre priechodný otvor | 16 ： 1 | |
| Povrchová úprava | HASL, Olovo bez HASL, ENIG, Immersion Cin, OSP, Immersion Silver, Gold Finger, Galvanické tvrdé zlato, Selektívne OSP ， ENEPIG.etc. | |
| Prostredníctvom možnosti Vyplniť | Priechodka je pokovovaná a naplnená vodivým alebo nevodivým epoxidom, potom prekrytá a pokovovaná (VIPPO) | |
| Medené, strieborné | ||
| Registrácia | ± 4 mil | |
| Spájkovacia maska | Zelená, červená, žltá, modrá, biela, čierna, fialová, matná čierna, matná zelená atď. | |
Môžete vyskúšať:
1, Zhrnutie záležitostiach vyžadujúcich pozornosť v spoji zváraní
3, Čo je PCB
4、Čo je to testovanie na bare?
Získajte viac informácií o produktoch YMS
